Pre-Terminated Fibre Cable

Starlight have developed a cost effective pre-terminated cabling system called OPAL™ (Optical Pre-Assembled Link) which is completely based around standard networking products. The system allows a fibre optic network to be installed in a fraction of the time taken by conventional on-site direct termination or fusion splicing. It requires no special installation skills or equipment, and can therefore be installed by non-specialist personnel, vastly reducing the installation cost.

The system consists of standard internal / external tight buffered distribution cable, which is supplied in specific lengths for each cable run in an installation. This cable is available in multimode or singlemode with fibre counts of 4, 8, 12, 16 or 24.

The cable is factory prepared in our in-house facility with a gland on each end which is epoxy bonded onto the Kevlar Strain Relief Yarn in the cable. The secondary coated fibres are terminated with either ST, SC, LC or FC-PC connectors which are fully tested and certified under our quality system. This ensures that the quality of the complete cable assembly is guaranteed before shipping to site.

A specially developed termination protection sleeve is fitted to each end of the cable assembly to protect the connectors during shipping and installation. This sleeve has a small diameter and is flexible, lightweight and extremely rugged. The protection sleeve connects onto the epoxy bonded cable gland and can withstand the high tensile loads applied when pulling cables through ducts. A pulling eye is incorporated to allow the attachment of a draw cable.

After cable installation, the protection sleeves are removed and the connectors are threaded through the gland hole of any cable management enclosure. A gland nut is used to secure the cable gland in place. Then the connectors are simply connected to the adaptors inside the enclosure to complete the installation.

Options:

  • Length - Choose the length for your requirements
  • Cores - 4, 8, 12, 16 & 24 Core
  • Connector Types - ST, SC & LC
  • Fibre Sizes - 50/125 (OM2), 50/125 (OM3) & 9/125 (OS2)
Please configure your Product from the drop downs o nthe right hand side of the page before adding to basket.

Features & Benefits:

  • Quick installation time
  • Low installation cost
  • Full test documentations supplied
  • No special fibre optic skills or equipment required
  • Factory terminated and tested
  • ST, SC LC connector options (multimode and singlemode)
  • 4, 8, 12, 16 & 24 fibre configurations
  • Standard cables and management enclosures
 
If you require the Pre-term to be made from Loose Tube Cable, specify this in the comments box at checkout. 

PLEASE NOTE THAT ANY CABLE CUT TO LENGTH HAS A 50% HANDLING FEE IF A RETURN IS REQUESTED

The following table shows the speed & recommended maximum distances for each fibre type-

 62.5/125 (OM1)50/125 (OM2)50/125 (OM3)50/125 (OM4)9/125 (OS1)
100Mbs2km2km2km2km40km
1Gbs275m550m800m1100m100km
10Gbs33m82m300m550m40km
40Gb / 100Gbs--100m125m40km

You might also like

  • Netgear ProSafe™ AGM731F
    Netgear ProSafe™ AGM731F
  • SC Loaded Break Out Box
    SC Loaded Break Out Box
  • SC Singlemode Fibre Pigtails
    SC Singlemode Fibre Pigtails
  • TP-LINK AV1000 Gigabit Powerline Starter Kit
    TP-LINK AV1000 Gigabit Powerline Starter Kit
  • External Armoured Cat6 UTP Solid Cable (Price Per Metre)
    External Armoured Cat6 UTP Solid Cable...
  • Power Meter
    Power Meter
  • LC Multimode Fibre Pigtails
    LC Multimode Fibre Pigtails
  • ST Lockable Wall Mounting Enclosure
    ST Lockable Wall Mounting Enclosure
  • TP-LINK MC200CM
    TP-LINK MC200CM
  • ST Loaded Break Out Box
    ST Loaded Break Out Box

Similar products

  • ST - ST Multimode Duplex Fibre Patch Leads
    ST - ST Multimode Duplex Fibre Patch Leads
  • ST - SC Multimode Duplex Fibre Patch Leads
    ST - SC Multimode Duplex Fibre Patch Leads
  • SC - SC Multimode Duplex Fibre Patch Leads
    SC - SC Multimode Duplex Fibre Patch Leads
  • LC - SC Multimode Duplex Fibre Patch Leads
    LC - SC Multimode Duplex Fibre Patch Leads

Pre-Terminated Fibre Cable

Pre-Terminated Multi-Core Fibre Cables Made to Your Specification.
Made & Tested in the UK 

CUSTOM

General Lead time 2-5 Day from order process. For current despatch date call or email

£0.00
£0.00 Ex VAT.